Home > Windows Xp > Windows XP - "System Is Not Fully Installed."

Windows XP - "System Is Not Fully Installed."

Contents

Networking issue - Dell ProBook... Hot Scripts offers tens of thousands of scripts you can use. Change the Boot-time Diagnostic Screen [Disabled] to Enabled Change the Quick Boot Mode [Enabled] to Disabled. If you still cannot get to Windows, do another non-destructive restore. Source

I'll finish setting it up tomorrow, hopefully avoiding any more major issues. http://www.bleepingcomputer.com/forums/t/527392/with-xp-ending-what-are-your-alternatives/ http://www.bleepingcomputer.com/forums/t/577719/never-tried-linux-before-read-this/ pcpunk eps2.4_m4ster-s1ave.aes_pcpunk_leavemehere Back to top Page 1 of 3 1 2 3 Next Back to Windows XP Home and Professional 0 user(s) are reading this topic IT WORKED!! Step 3: Editing SystemSetupInProgress value Use the following steps to edit the value: In the registry editor window, double-click HKEY_LOCAL_MACHINE, and then double-click temphive. https://social.technet.microsoft.com/Forums/windows/en-US/ab4032f4-3ab8-4997-92a5-ad6fa332c047/system-not-fully-installed-please-run-setup-again-problem-for-xp?forum=itproxpsp

Your System Is Not Fully Configured

Ask a question and give support. f. sach2, Jun 6, 2011 #9 rtxx Private E-2 sach2 said: ↑ I've been reading and I think I would do the recovery one more time, but before doing the recovery try All rights reserved.

Staff Online Now etaf Moderator Advertisement Tech Support Guy Home Forums > Operating Systems > Windows XP > Home Forums Forums Quick Links Search Forums Recent Posts Members Members Quick Links Last edited: Jun 7, 2011 rtxx, Jun 7, 2011 #10 sach2 Major Geek Extraordinaire Good work! Ask the community! I don't think that recovery should take more than 90 minutes even though my link says it can take hours.

My thanks also to JohnC_21 and Agouti for all their help and anyone else who may have submitted a reply but whose reply I have not read yet and who have After running Sysprep, Windows XP posts event 1517 to the Application log after the first restart? Your directions were clear and on point and I am indebted to you. Privacy statement  © 2017 Microsoft.

Related support Microsoft support article, "The system is not fully installed" error message after you run Sysprep and restart (in English). Please run setup again. However, serious problems might occur if you modify the registry incorrectly. The Recovery Console is not listed in the OS choice screen.

  • Unfortunately, this is the only computer I have access to that could have downloaded anything onto a bootable drive.
  • Locate the %SystemRoot%system32Config folder, rename the System file to System.erd, and then rename the System.mini file to System. 7.
  • Back to top #12 Leurgy Leurgy Voted most likely Members 3,831 posts OFFLINE Gender:Male Location:Collingwood, Ontario, Canada Local time:02:19 AM Posted 17 February 2016 - 11:29 AM It would really
  • Community Sponsors Advertisement WindowsITPro.com Windows Exchange Server SharePoint Virtualization Cloud Systems Management Site Features Contact Us Awards Community Sponsors Media Center RSS Sitemap Site Archive View Mobile Site Penton Privacy Policy

Recovery Console Windows Xp

Exit Recovery Console and then restart to the original operating system. click here now If that actually does show 2006 its important that you go in there and change that to reflect the true date. Your System Is Not Fully Configured Open the System file. 08. If booting into safe mode, this same message appears after the screen with "Safe Mode" showing in all 4 corners appears.

He DID attempt nondestructive system recovery. this contact form Boot the parallel install. 03. It then proceeded with setting up the computer, setting the time zone, computer name, etc. AllenS, Aug 8, 2011 #14 AllenS Private E-2 tgell said: ↑ Hello, Since you cannot boot the computer, you will have to add the log file offline using either a WinPE

please select this option. note: Certain LCD flat panel monitors may prevent or delay the initial computer software setup. The Recovery Console will start and ask you which Windows installation you would like to log on to. http://upxpress.net/windows-xp/windows-xp-not-fully-bootingup.php I do as you did and just change the geometry to make it happy.

I tried TestDisk. Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

Login I even tried a nondestructive recovery with the CRT monitor.

What are your recovery options using the HP/Compaq CDs? (I don't see why an old CRT monitor would cause any problems).

And reporting 255 vs 240 for this particular drive has no effect on drive function, right? Select (highlight) the HKEY_LOCAL_MACHINE hive. 05. It gave a result as far as I got (there is a regular partition and a recovery partition) Warning: Incorrect number of heads/cylinder 240 (NTFS) != 255 (HD) 1 * HPFS-NTFS You may also...

Press OK. 12. If you choose to participate, the online survey will be presented to you when you leave the Technet Web site.Would you like to participate? Please start a New Thread if you're having a similar issue.View our Welcome Guide to learn how to use this site. http://upxpress.net/windows-xp/windows-xp-just-installed.php You wont get the message anymore and you'll be able to boot to your normal environment.Click to expand...

AllenS, Aug 15, 2011 #15 AllenS Private E-2 AllenS said: ↑ tgell said: ↑ Hello, Since you cannot boot the computer, you will have to add the log file offline using To use the Microsoft Windows Recovery Console option, start the computer with the Windows XP installation CD-ROM in Recovery Console. 2. Nothing wrong except for a few missing files. If you have to reinstall XP to get the PC to work and don't want to affect the old OS and data just install it a different folder, such as WINXP.

The testdisk looks normal and the asterisk denotes that C: is the active partition. On the Registry menu click File, click Load Hive, open the %SystemRoot%System32ConfigSystem.mini registry file, and then type Test.NOTE: You can use any name for the hive you load except System.